Caffewerks Water Pump System Install Guides
Short answer: a Caffewerks water pump system installs in about nine steps with no tools beyond the included tubing cutter, pliers and an adjustable wrench. You run 3/8" beverage tubing from a pickup tube in your fresh water container to the pump, then to your pitcher rinser, an optional filter and your espresso machine. Then you power it up and purge the air. Connect Cube systems use quick-connect plugs instead of cut tubing, so they go together even faster.
This page covers both system types. Jump to yours:
- Connect Cube Hydro (case system)
- Complete Cart Components (panel system: Medium Volume, High Volume, Home)
- Install FAQ
Before you start: tubing, push-fit fittings and locking clips
- Cutting tubing: set the tubing in the V of the Caffewerks tubing cutter and squeeze evenly. Every cut should be square and clean.
- Making a push-fit connection: push the tubing into the fitting with even pressure until it reaches the pipe stop, then pull back to check that it holds.
- Removing tubing: depressurize the system first. Push the collet toward the fitting and pull the tube out.
- Locking clips: once the system is set up, slide a locking clip onto the collet of every push-fit fitting so the connection cannot release.
Each install kit includes 6 ft of beverage tubing, an on/off valve and a one-way check valve.
Connect Cube Hydro installation
Printable Connect Cube install guide
What's in the box
- Connect Cube Hydro
- 2 install kits: espresso machine and pitcher rinser
- Fresh water pickup tube for a 7-gallon Aquatainer
- Optional: Connect Cube Filtro, and extra install kits for a coffee brewer or sink
Steps
- Place everything. Put the Hydro, the fresh water container and the waste water container where they will live on your cart, table or trailer. Fill the fresh water container. Have the waste container ready for the drain hoses.
- Connect the pickup tube. Press the 3/8" beverage tubing firmly into the push-fit fitting on top of the pickup tube and lock it with a clip. Drop the pickup tube into the fresh water container, then plug its female quick-connect into the Hydro inlet.
- Install the pitcher rinser. Thread the BSP elbow fitting onto the bottom of the rinser with the silicone gasket in place. Run the drain hose from the rinser drain into the waste container. Plug the rinser kit's male quick-connect into one of the Hydro outlets.
- Connect the espresso machine. Attach the braided steel hose from your machine to the install kit fitting. Tighten with pliers and lock the push-fit fitting with a clip.
- Add filtration (optional). Use the connection manifold packed in the Filtro box to run the Hydro outlet into the Filtro inlet. The Hydro and Filtro can be stacked to save space.
- Finish the setup. Turn on the espresso machine and let it fill its internal tank. Run water through the group head and the rinser for a few seconds to clear air from the tubing. Let the machine heat up before use. Make sure every drain, from both the machine and the rinser, runs into the waste container.
Complete Cart Components installation (panel systems)
Printable Complete Cart Components install guide
What's in the box
- Water pump system (pump and accumulator)
- Fresh water pickup tube
- Caffewerks tubing cutter
- Espresso machine install kit, and a rinser install kit (not included with the Home Panel)
- Push connectors
Steps
- Check your fittings and place everything. Confirm you have the right fittings for your machine (see step 6). Place the pump system, fresh water container and waste container. Fill the fresh water container.
- Connect the pickup tube. Press 3/8" beverage tubing firmly into the push-fit fitting on top of the pickup tube, then place it in the fresh water container.
- Connect the pump. Run tubing from the pickup tube to the pump's inlet side. Leave enough slack to lift out the container and pickup tube for refills. Make a square cut with the tubing cutter, push the tube into the pump inlet and lock it with a clip.
- Install the pitcher rinser (if you have one). Push tubing into the pump outlet tee and run it to the rinser location, then fit the push-fit tee. Tighten the 1/2" BSP elbow onto the rinser valve with the flat silicone washer. Using short lengths of tubing between them, install in order: on/off valve, check valve, then the 1/2" BSP elbow. Run the drain hose to the waste container.
- Install filtration (optional, recommended if you fill from a tap). From the tee by the rinser, run tubing into the filter inlet, and from the filter outlet toward the espresso machine. Caffewerks offers 6" and 10" inline carbon filters, and the Dual Stage Filter (sediment plus carbon block) for longer life.
- Connect the espresso machine. Find the fitting that matches the braided stainless hose that came with your machine: 3/8" BSP, 9/16" UNF or 1/4" BSP. Using short lengths of tubing between them, install the on/off valve, then the check valve, then that fitting. Connect the filter's outlet tubing to the machine input. Snug fittings with pliers and an adjustable wrench without overtightening.
- Start the system and purge air. Make sure every connection has its locking clip. Plug in and power the pump. Open the pitcher rinser to push air out. Let the accumulator come up to pressure (about 60 PSI).
- Flush the filter. Turn on water to the filter, slowly open the valve at the filter outlet to release air, and flush at least half a gallon to clear carbon particles.
- Make the final machine connection. Attach the braided steel hose to the espresso machine, check that it is tight, then power on the machine and confirm water is flowing.
After install: checks and maintenance
- Check connections and fittings regularly for leaks and firm seating.
- Replace filters on schedule. See the Filtro and Dual Stage filter replacement guide.
- Do not adjust the accumulator or pump pressure. The accumulator is pre-set at the shop, and changing the air pressure or pump settings voids the warranty.
Something not right? Start with the water pump troubleshooting guide, or email info@caffewerks.com.
Install FAQ
Which system do I need?
The Connect Cube Hydro (1.5 GPM) is a self-contained case with plug-in quick connects. The Hydro HV (3.2 GPM) is for higher-draw setups. Panel systems (Complete Cart Components) mount to your cart. See which Connect Cube system you need and the coffee cart plumbing guide for sizing.
Will it work with my espresso machine?
Caffewerks water pump systems work with all espresso machine brands. Install kits include the most common fittings for connecting your machine's braided line: 3/8" BSP, 9/16" UNF and 1/4" BSP.
What pressure does the system run at?
The accumulator is pre-set and pressurizes to about 60 PSI. Do not adjust it, because that voids the warranty.
Do I need a water filter?
It's recommended if you fill your fresh water container from a tap. A filter limits mineral build-up in your machine and improves taste.
How long until my system ships?
Water pumps and electrical systems are built to order, with a 7–10 day lead time before shipping. See shipping.
Can I ship a pump system outside the USA?
No. Water pump systems and electrical products ship within the USA only.
Leave a comment