Water Pump Fittings

These quick connection fittings make removal of equipment and devices easy.

Four inches of 3/8 OD tubing is provided on each connector. Each kit includes one female and one male quick connect.

Easy installation into our push fittings.  Additional fittings maybe required to connect inline with components. 

The locking clip secures the collet in a locked position after the tubing has been inserted. This prevents the accidental release of tubing. The clip is easy to remove if the tubing needs to be released.  

Features:

• Used to secure the collet in a locked position
• Prevents accidental disconnection of the tubing
• Easily removed

Notes:

• Locking clips should be inserted only after tubing is fully inserted to prevent scraping of the tube. 

A 3/8" Tube Stem Run Tee. 

• Leak Resistant EPDM O-rings
  
• Chemical Resistant Polypropylene
  
• Certified to NSF/ANSI Standard 58
  
• 304 Stainless Steel Gripping Teeth
• 150 p.s.i. @ 70ºF (10 Bar @ 20ºC)
  
• 60 p.s.i. @ 140ºF (4 Bar @ 60ºC)
  
• For use with Plastic or Soft Metal Tubing

• Color : white
• Material : Polypropylene
• NSF/ANSI Certified : Yes
• O-Rings : EPDM

Email or fill out question box below with any questions 

By maintaining a consistent and controlled water pressure, a pressure regulator helps prevent damage to plumbing fixtures, appliances, and pipes due to excessive pressure. It ensures a steady flow of water throughout the system, promoting efficient operation and prolonging the lifespan of the components.  

Push Fit 3/8" Tube X 3/8" Female BSP

• Leak Resistant Dual EPDM O-rings
  
• Chemical Resistant Polypropylene
  
• Certified to NSF/ANSI Standard 58
  
• 304 Stainless Steel Gripping Teeth
• 150 p.s.i. @ 70ºF (10 Bar @ 20ºC)
  
• 60 p.s.i. @ 140ºF (4 Bar @ 60ºC)
  
• For use with Plastic or Soft Metal Tubing

• Color : Grey
• Material : Polypropylene
• NSF/ANSI Certified : Yes
• O-Rings : EPDM (x1)

*manufacturer may vary*

Omnipure K Series Inline Filters - GAC/Scale Reduction -  K2586KK

2"x10"-3/8" Quick-Connect GAC/Polyphosphate Filter

A simple solution for inline filtration running to your espresso machine or water tap. 3/8"Push Fit fittings compatible with all Caffewerks Water Pump Systems.

Documents for Item 

Specification Sheets

• For Compliance with Prop 65 Arsenic: Flush all carbon filters at the rated flow rate for 5+ minutes prior to using water from filter.

If backordered, estimated lead time is: 2-3 Weeks

Omnipure K Series Inline Filters - GAC/Scale Reduction -  K2386KK

2x6"-3/8" Quick-Connect GAC/Polyphosphate Filter

A simple solution for inline filtration running to your espresso machine or water tap. 3/8"Push Fit fittings compatible with all Caffewerks Water Pump Systems.

Documents for Item 

Specification Sheets

• For Compliance with Prop 65 Arsenic: Flush all carbon filters at the rated flow rate for 5+ minutes prior to using water from filter.

This fitting is used on some espresso machine brands like the Lucca / La Spaziale range of machines.

This pitcher rinser connection fitting is Push Fit 3/8 tube x 1/2 BSP 90 degree elbow.

That elusive piece that you can’t buy at the hardware store. 

If you are installing a rinser in a low profile setting this helps get it done.

Looking for the straight version of the rinser fitting?

These quick connection fittings make removal of equipment and devices easy.

These Push Fit 3/8” x Quick Connect are made of rugged FDA approved Acetal Plastic. Each connector has a built in check valve so no water is lost during disconnected transport. Each kit includes one female and one male quick connect.

Available as individual Male and Female parts as well. 

Easy installation just like all of our push fittings.